ECLIPSE® R2000 Laser System

Laser Cleaning System


The best just keeps getting better.  Are you looking for the fastest, safest and most effective way to deep clean your anilox rolls?

The Eclipse® R2000 Laser Cleaning System is the fastest anilox cleaning system on the market today.  Easily clean any type of ink, coating or residue using our patented circular laser technology that ensures a perfect clean that is safe on your rolls, even after the 1000th cleaning!

See below for a full breakdown of the science behind it.


  • Green technology = chemical and waste-free, no cleaning media required
  • No cleaning media means no consumable to purchase!
  • No compressed air or water needed, only electric
  • Fully automated, can be left unattended without worry
  • Class I Laser System = no safety glasses required
  • Meets/exceeds OSHA requirements for industrial laser systems


Did you know that our patented circular laser technology is being used in Paris to restore the legendary Notre-Dame Cathedral back to its former glory following the fire that gutted it in 2019?

Watch this report to see how our safe & effective laser tech can be used on something as precious as a centuries-old monument.  The same tech has been used to clean a 3500 year old Egyptian monolith as well as the legendary marble lions outside the New York City Public Library!

Curious if laser cleaning is right for you and your roll cleaning needs?  Contact us today to schedule a free demo!

laser Beam

circular vs. linear

Our circular laser scan technology eliminates the possibility of hot spot related roll damage that is commonly associated with traditional linear/line scanning systems currently on the market.

PROUDLY MADE in the u.s.a.

Unlike most laser systems on the market today with Chinese-made laser sources, our patented laser system is 100% made right here in the United States!

faster. safer. cleaner.

Our technology removes nearly any type of adhesive, ink or coating off of nearly any type of roll, faster than any other one-head laser system available!

  • 50 Watt industrial laser – our system design is OSHA compliant and rated as a Class 1 laser which means to laser goggles required.
  • Auto-shutoff safety features include interlock feature that will shut the system down if the lid/door is opened or if the roll stops spinning while the cleaning cycle is underway.
  • Full enclosed and properly marked & labeled as a laser containing system.
  • Physical key switch and password-protected PLC.
  • Laser assisted focus
  • Laser cleaning speed is about 2-6 inches (51-152 mm) per minute, depending on roll diameter, residue build-up and residue type.
  • Easily fine tune parameters by controlling the laser pulse frequency, RPM, scanning speed, roll surface speed and number of cleaning cycles.
  • Laser system does not create retained head on roll being cleaning.
  • Built-in countdown clock to indicate remaining cleaning time.
  • Beacon light and sound indicates cycle start and end times.
  • Sensors will indicate if there is an air flow or filter issue.
  • Properly-rated real time viewing windows with internal LED lighting.
  • Electric requirements = 240V
  • Auto-measuring feature for roll length and diameter
  • Save individual roll cleaning settings for future use
  • System includes USB port for remote access through a laptop for system updates and remote diagnostics

Critical Values to Understand When Evaluating Roll Cleaning Systems

The ARCS Eclipse® Laser Cleaning System uses a 50-watt laser source. We have been asked if this is too much power – it is not! Please see below to learn more about laser Watts and how they directly correlate to Pulse Frequency – understanding these two concepts is key when attempting to compare the Eclipse® System to other laser systems found on the market today. With the right settings used, laser roll cleaning can produce fabulous cleaning results. When the wrong settings are used, it can lead to roll damage.

The below explanation covers a lot of technical material – we welcome any follow up inquiries to discuss this information further – please feel free to call us at any time or send us an email. 

For this topic, it’s impossible to discuss Laser Watts without also including an explanation of Pulse Frequency.  A system’s wattage tells only half of the story. In order to know how the whole system functions and what constitutes safe settings vs. unsafe settings, you also need to know its Pulse Frequency, which is also referred to as Repetition Rate.  Combining both numbers into a simple formula will give you a system’s overall energy output, which is where we start:

How is Laser Energy Measured?

In millijoules (mJ). Well, that was easy! Not quite.

We first need to understand how to define a Joule and Millijoule:

A Joule (J) is one unit of energy. Laser energy is expressed in Millijoules (mJ) which is 1 thousandth of a Joule. So, what does THAT mean?  Well…

1 Joule = The energy dissipated as heat when an electric current of one ampere passes through a resistance of one ohm for one second.

Here are two examples:

  1. One Joule is the amount of energy required to lift a medium-size tomato (100 g) 1 m vertically from the surface of the Earth.
  2. One Joule is the amount of electricity required to light a 1-watt LED for 1 second.

Millijoule (mJ) Formula
A millijoule (mJ) is 1 thousandth of a Joule, just a tiny fraction of energy! And when cleaning anilox rolls, the fraction of energy gets even tinier. Through extensive testing we have determined most aniloxes can be cleaned safely when using a .2 mJ setting or thereabouts. A key point here is that when considering using a laser system, you must consider more than just the number of watts the system offers. It is just as critical to know and understand Pulse Frequency. Both values are required to calculate mJ – just focusing on watts alone does not tell the full story.

How do you calculate mJ? 

If you know BOTH the wattage level AND the pulse frequency value, millijoules can be easily calculated using the below formula:

Formula:  mJ = Watts DIVIDED by Pulse Frequency 

A key point here is when considering using a laser system, you must take into account more than just the number of watts the system offers. It is just as critical to know and understand Pulse Frequency

Both values are required to calculate mJ – just focusing on watts alone does not tell the full story.

How do you calculate mJ? 

If you know BOTH the wattage level AND the pulse frequency value, millijoules can be easily calculated using the below formula:

Formula:  mJ = Watts DIVIDED by Pulse Frequency 

Watts Explained with a Car Analogy
Don’t think of watts like you think about a light bulb.  Instead, let’s use a car analogy.  If we want to drive up a steep mountain, most people will agree they would rather take a car with a 6- or 8-cylinder motor to power us up the hill – the risk of overheating the engine is less, and our vehicle won’t get strained along the way.  Should we instead drive up the incline with a compact car that uses a 4-cylinder engine, by the time we get to the top our engine will be hot to the touch – this is where the expression “its running hot” comes from. 

The same principle applies to laser systems. The laser source of a system is what we call the “platform”.  A higher wattage system is like using a larger motor in a car – everything runs better and much “cooler”. The Eclipse System uses a 50W “platform”. This means we can use a much lower pulse frequency setting, and as you will see below, the pulse frequency of a laser is the more important variable to understand and control to avoid potential roll damage.

Pulse Frequency Explained with a Fire Hose Analogy
Measured in kilohertz (kHz) and also known as repetition rate, pulse frequency refers to the number of times the laser “fires” per second. Although the laser beam appears to be a continuous wave of light, the beam would look more like a dotted line if we could look at it in slow motion. Higher kHz values mean overall lower intensity laser energy. This is what we offer – a system that uses GENTLE pulse frequency settings. Lower values, which are used by other manufacturers will increase the amount of laser energy, which in turn generates more heat and can cause roll surface damage.

When pulse frequency is set too aggressively, there is a strong likelihood it will cause a condition called “micro-melting” or “micro-fractures” on the roll surface. Low pulse frequency settings generate too much photothermal energy (i.e., heat) for the engraved surface to withstand, which can lead to cell damage. Put another way, when we fire the laser less times per second, it results in a more powerful “burst” of energy with each ensuing pulse. The laser energy has no place to go when it’s not firing, so it just continues to build up and up until it fires again.  When we increase the pulse frequency setting so that the laser fires more pulses per second, the photothermal energy is lessened because there is no opportunity for it to build up.

Think of a fire hose – when it’s first turned on, it is very hard to control because the initial “burst” of water has been held under extreme pressure.  Imagine turning off that same hose for a full minute and then turning it on again. That same difficult to control burst of water will occur again. In this example, because we are waiting a whole minute between hose bursts, we have given the water plenty of time to build up pressure before releasing it, resulting in a tremendous amount of energy escaping from the hose nozzle as soon as we turn the valve on every time.

Now think of that same hose turned on and off once per second. The hose will be much easier to control because the water pressure doesn’t have time to build up.  This same principle applies to pulse frequency – the higher the repetition rate, the less time the laser has to build up its energy, which allows the laser to do its job of cleaning a roll vs. damaging it.

Watts + Pulse Frequency with Another Car Analogy
Striking the right balance between watts and pulse frequency so that a roll gets thoroughly cleaned but the cells do not get altered in any way is much harder than it looks. If we go back to the original car analogy we used, think of it this way: A larger motor needs less RPM (rotations per minute) to drive 60 mph and a smaller motor requires more RPM to go at the same speed. In other words, smaller motors need to work harder than larger ones. 

A larger laser source operates on the same principle.  A 50-watt system like ours uses a gentle pulse frequency to remove dried ink and coatings, ensuring the process remains safe for your roll every time.  A lower watt system requires a stronger, more aggressive pulse frequency setting in order to perform cleaning. Unfortunately, using more pulse frequency can quickly lead to roll damage. We have witnessed first-hand other laser systems on the market today damage rolls because their systems rely more on pulse frequency than they should to perform the cleaning. Although this approach is less expensive up front (a lower watt laser will always cost less than one with more watts), it creates a risky situation that ultimately could cause the cheaper system to become much costlier in the long run due to cell damage which results in roll resurfacing and replacement costs.

mJ Formula Examples

In most cases, .2 millijoules (mJ) or less is the right amount of energy to clean an anilox roll provided the pulse frequency is set to at least 200 kHz (or higher) – this is a key point and is discussed further in a little bit.

In the below example, when the pulse frequency on our 50-watt laser is set to 300 kHz, it will produce .16 mJ:

Formula:       50 W
                       300 kHz = .16 mJ

Again, more watts mean less pulse frequency needed. 

If we use a lower watt system but keep the pulse frequency value the same, we come up with less overall laser energy being produced:

           30 W
          300 kHz = .10 mJ*

          20 W
          300 kHz = .06 mJ*

*  We have discovered this is an insufficient level of energy for effective removal of most inks and coatings on the market today.

Eclipse® vs. Other Systems
So, let’s see how the Eclipse Laser Cleaner at 50 watts compares to 30 and 20-watt systems.  Remember that the lower the pulse frequency (aka repetition rate) equals MORE photothermal energy (heat).

Formula:  mJ = Watts / Pulse Frequency

This table shows how many mJ get produced depending on the combination of watts and pulse frequency used. Our testing has shown when pulse frequency is below 100 kHz, it has the potential to cause roll damage. Pulse frequency is independent of watts in this case – no matter if you are using a low or higher watt system like ours, we do not recommend cleaning rolls using such a low pulse frequency.  

Car Analogy Revisited

But wait – above it says a .2 mJ energy level is safe? Correct. Doesn’t the table show the competition only producing .2 or .3 mJ at 100 kHz? Yes. But…. don’t forget about the car analogy.  The competitions “platform” (4-cylinder engine going up the mountain) requires the motor to run hot and possibly overheat before it even reaches the summit.  Our “platform” (6-cylinder motor going up the mountain) runs cooler even when it goes faster.

Other lower watt systems need to make up for this undersized “motor” by using more aggressive pulse frequency settings– if they didn’t their laser would never clean a roll.  In other words, a roll can get damaged even if the actual mJ produced is lower – the pulse frequency matters more than watts and does have a threshold that shouldn’t be crossed (see red row above).  When it is, the following can happen:

When lower watt systems try to avoid this situation and use a “gentler” pulse frequency, it lessens the overall energy (mJ) being used (see yellow boxes in above table), which results in either a slower cleaning cycle or inconsistent / poor cleaning outcomes altogether.

We even know of a company that only uses 70% of their 20-watt laser source, or 14 watts.  This means it will take even longer to clean a roll, as their system must slow down a lot for it to work without harming a roll surface.

Everything you have just read boils down to this:  lasers can damage rolls if the proper settings aren’t used.  Our deep understanding of how this technology functions and extensive experience cleaning hundreds of client rolls gives us the know-how needed to help companies with their roll cleaning needs.  The Eclipse Laser Anilox Roll Cleaning System operates in a safe zone, one which rides on the right “platform” (50 watts) enabling it to clean using optimal pulse frequency settings (see green boxes above).